Torqeedo electric outboard brings a whole new refreshing change after switching from a gas powered one, especially when you are considering going downstream for fishing. Its maintenance cost is often considered to be less expensive. Additionally, it rarely needs any maintenance.
The gas powered outboards are usually very easy to operate due to the fact that they are able to provide a high mileage. Regardless of this fact, they pose grave danger to the environment as well as having a pretty higher maintenance cost. A much cheaper solution is to convert an old gas powered outboard to an electric one, rather than considering purchase of a new one.
Changing the muffler is the simplest conversion process. However, the best option would be to change an old gasoline type into an electric one. The steps outlined below will guide you in doing so.
The gas powered one is supposed to be switched off first. A screwdriver should then be used to unscrew the casing on it. By using a wrench, unbolt the gas tank, lifting it up.
Next, remove the bolts from the motor and separate it from the engine. Following this, remove the bolts from the pistons and cylinders. Take out the gas motor and replace it with the electric one in its position.
Immediately after fixing the electric one, attach the motor and simultaneously drive the shaft together and align them. The two separate tips should be perpendicular to each other. As you try to twist its drive shaft, the motor should also twist or turn.
The motor should then be attached in position tightly. Unscrew the control panel by removing the wires out of the socket. Lift up the control panel after pulling out the wires. The control panel should be replaced using a 300-amp and then reconnect the wires back as before. You can now place back the case after removing the battery sockets out of the engine.
You will now be required to drill a few holes at the rear of the boat on the engine bracket. Drill should tree in total; at one end of the leather strap and two more, one on each side of the rack. The strap end should then be fixed to the left side hole by bolting it.
You will now be required to set the six batteries side by side and then pull the strap over to cover them tightly. Drill one hole into the strap and then bolt it. After doing so, the device is now bolted and attached to the engine bracket.
The outboard having been bolted, the positive wire that is initiated from the battery on the left should be reconnected to the negative socket located on the right. In the same manner, the reconnection should also be done between the negative wire and the negative socket. It is important to arrange the batteries in a series. Finally, you need to connect the positive socket in the controller to the positive wire at the battery on the right. With all these steps completed, you can take your Torqeedo electric outboard to that fishing trip.
The gas powered outboards are usually very easy to operate due to the fact that they are able to provide a high mileage. Regardless of this fact, they pose grave danger to the environment as well as having a pretty higher maintenance cost. A much cheaper solution is to convert an old gas powered outboard to an electric one, rather than considering purchase of a new one.
Changing the muffler is the simplest conversion process. However, the best option would be to change an old gasoline type into an electric one. The steps outlined below will guide you in doing so.
The gas powered one is supposed to be switched off first. A screwdriver should then be used to unscrew the casing on it. By using a wrench, unbolt the gas tank, lifting it up.
Next, remove the bolts from the motor and separate it from the engine. Following this, remove the bolts from the pistons and cylinders. Take out the gas motor and replace it with the electric one in its position.
Immediately after fixing the electric one, attach the motor and simultaneously drive the shaft together and align them. The two separate tips should be perpendicular to each other. As you try to twist its drive shaft, the motor should also twist or turn.
The motor should then be attached in position tightly. Unscrew the control panel by removing the wires out of the socket. Lift up the control panel after pulling out the wires. The control panel should be replaced using a 300-amp and then reconnect the wires back as before. You can now place back the case after removing the battery sockets out of the engine.
You will now be required to drill a few holes at the rear of the boat on the engine bracket. Drill should tree in total; at one end of the leather strap and two more, one on each side of the rack. The strap end should then be fixed to the left side hole by bolting it.
You will now be required to set the six batteries side by side and then pull the strap over to cover them tightly. Drill one hole into the strap and then bolt it. After doing so, the device is now bolted and attached to the engine bracket.
The outboard having been bolted, the positive wire that is initiated from the battery on the left should be reconnected to the negative socket located on the right. In the same manner, the reconnection should also be done between the negative wire and the negative socket. It is important to arrange the batteries in a series. Finally, you need to connect the positive socket in the controller to the positive wire at the battery on the right. With all these steps completed, you can take your Torqeedo electric outboard to that fishing trip.
About the Author:
Read more about Switching From A Gasoline Powered To Torqeedo Electric Outboard visiting our website.
No comments:
Post a Comment